Home What's New Careers Products Customer Support Downloads About Us

Micro ATE QT-2216
Specifications

  1. Main Board Houses the Main Test Vector Processor
    1. Interface to the Host PCI card.
    2. 8 Slots for resource cards.
    3. Interface to the device specific Load Board through 256 pin Pogo pins.
    4. Slot 1 DPPS1.
    5. Slot 2 PMU1.
    6. Slot 3 Digital Card.
    7. Slot 4 Digital I/O for Load Board.
    8. Slot 5 AC PMU.
    9. Slot 6 Digital Card.
    10. Slot 7 High Voltage / High Current PMU2.
    11. Slot 8 High Voltage / High Current DPPS2.

    2. Each PMU has two independent channels for FVMC, FCMV and Waveform Digitizer at 20Msps.

  2. 4 ranges for force voltage / measure voltage;
    1. +/– 0.5v FS.
    2. +/– 6v FS.
    3. +/– 13v FS.

  3. 6 Ranges for Measure Current / force current mode;
    1. +/– 50mA range with Resolution of 25ľA.
    2. +/– 5mA range with Resolution of 2.5ľA.
    3. +/– 500ľA range with Resolution of 250nA.
    4. +/– 50ľA range with Resolution of 25nA.
    5. +/– 5ľA range with Resolution of 2.5nA.
    6. +/– 500nA range with Resolution of 250pA.

    4. Each PMU one High Voltage / High Current channel for FVMC and FCMV.

  4. 2 ranges for force voltage / measure voltage;
    1. +/– 24v FS.
    2. +/– 48v FS.

  5. 4 ranges for Measure Current / force current mode;
    1. +/– 5A range with Resolution of 2.5mA.
    2. +/– 500mA range with Resolution of 25ľA.
    3. +/– 50mA range with Resolution of 250ľA.
    4. +/– 5mA range with Resolution of 25ľA.

    6. Each DPPS has two independent programmable power supply for the device under test.

  6. Force voltage - Measure Current Mode

  7. Supply programmable from –12v to +12v in steps of 5.86mV

  8. RAM based DPPS for drive voltage and measure current with 4k depth and time bas programmable

  9. 4 Current Measure Ranges from
    1. +/– 100mA FS (48ľA Resolution).
    2. +/– 10mA FS (4.8ľA Resolution).
    3. +/– 1mA FS (480nA Resolution).
    4. +/– 100ľA FS (48nA Resolution).

    10. Each Digital Card has 8 channels with 4k X 8 RAM behind each pin.

  10. Each Driver can drive Logic One / Zero / Hi-Z state or Terminate to a preprogrammed voltage within –2v to +7v

  11. Logic Levels are programmable from –2v to +7v in 10mV steps

  12. Each Driver can choose its drive levels from either one of the preprogrammed pallets.

  13. Each Pin Receiver has programmble upper and lower thresholds within the range of –2v to +7v and can be selected for each pin receiver from either one of the preprogrammed pallets.

  14. 2 bit compare RAM and 2 bit acquisition RAMS are provided for both hardware compare and for reading fault date for FA.

  15. Pull-up, Pull-Down, Both or None are user programmble for each pin.

  16. Uses Digital Highway 0 for measurement of frequency through any pin receiver and uses the pin receiver thresholds.

  17. Maximum frequency of measurement is 50MHz.

  18. Digital Highway 1 is used for pulse width measurement of any signal routed through pin receiver and using the pin receiver thresholds.

  19. Digital Highway 2 is also used for pulse width measurement simultaneously.

  20. It is also possible to measure time between two events occuring at Digital highway 1 and 2.

  21. Time resolution is 1ns.

Micro ATE QT-2216
Overview
Specifications